In light of the recent release of Marshall's Origin series, I'd like to ask the forum: How does power scaling work? Many tube amps these days offer the ability to switch from full power down to half or even 1/10 of the total output wattage. How does this work? How can you reduce the amount of power the tubes are pushing and still get the same tone? Does this effect the amount of power tube distortion you can get? Any and all insight would be greatly appreciated.
Announcement
Collapse
No announcement yet.
How does tube power scaling work?
Collapse
X
-
Re: How does tube power scaling work?
Originally posted by devastone View PostOriginally posted by crusty philtrumAnd that's probably because most people with electric guitars seem more interested in their own performance rather than the effect on the listener ... in fact i don't think many people who own electric guitars even give a poop about the effect on a listener. Which is why many people play electric guitars but very very few of them are actually musicians.
Comment
-
Re: How does tube power scaling work?
Originally posted by dystrust View PostThat's how full power scaling works. For amps with a simple wattage switch (like my Marshall Mini Jubilee) I suspect that the power transformer has additional secondary tap(s). It essentially runs the power tubes at lower plate voltage which reduces total wattage and headroom along with it."So understand/Don't waste your time always searching for those wasted years/Face up, make your stand/And realize you're living in the golden years"
Iron Maiden - Wasted Years
Comment
-
Re: How does tube power scaling work?
Totally different, it runs the pentode power tubes as triodes, for a better explanation there is google. The original question was about power scaling, I think that is pretty much the only way to get a 90% reduction in power, not sure the power tubes would even work at a low enough plate voltage to do that (although, it has been well documented that I could be wrong).
Comment
-
Re: How does tube power scaling work?
Originally posted by Jacew View PostWhat about pentode/triode switching?Originally posted by crusty philtrumAnd that's probably because most people with electric guitars seem more interested in their own performance rather than the effect on the listener ... in fact i don't think many people who own electric guitars even give a poop about the effect on a listener. Which is why many people play electric guitars but very very few of them are actually musicians.
Comment
-
Re: How does tube power scaling work?
Originally posted by devastone View PostTotally different, it runs the pentode power tubes as triodes, for a better explanation there is google. The original question was about power scaling, I think that is pretty much the only way to get a 90% reduction in power, not sure the power tubes would even work at a low enough plate voltage to do that (although, it has been well documented that I could be wrong).Originally posted by crusty philtrumAnd that's probably because most people with electric guitars seem more interested in their own performance rather than the effect on the listener ... in fact i don't think many people who own electric guitars even give a poop about the effect on a listener. Which is why many people play electric guitars but very very few of them are actually musicians.
Comment
-
Re: How does tube power scaling work?
Originally posted by jakester10 View PostIn light of the recent release of Marshall's Origin series, I'd like to ask the forum: How does power scaling work? Many tube amps these days offer the ability to switch from full power down to half or even 1/10 of the total output wattage. How does this work? How can you reduce the amount of power the tubes are pushing and still get the same tone? Does this effect the amount of power tube distortion you can get? Any and all insight would be greatly appreciated.
Hey everybody,
Thanks for responding to my thread. I did a little research of my own with your posts helping to guide my search, and I found this article, which has some of the technical jargon that I was looking for.
Comment
-
Re: How does tube power scaling work?
Originally posted by dystrust View PostSwitching from pentode to triode does reduce wattage, but it substantially changes both the tone and feel of the power tubes. My Jubilee 2555 has pentode/triode switching and I never use it because 'low' power mode sounds like spongy, muddy crap. With the Mini OTOH, low power sounds almost identical to high power just a bit more spongy and less loud.
I agree with "low power mode" sounding spongy and undefined in TT too. It improved greatly, when I added separate cathode resistor for the 7 watt side though."So understand/Don't waste your time always searching for those wasted years/Face up, make your stand/And realize you're living in the golden years"
Iron Maiden - Wasted Years
Comment
-
Re: How does tube power scaling work?
Another way I see this done, not sure if it's a method already described and marketed differently or another a whole new way... heck, I'm not even sure how they achieve it; but my Traynor does Class switching. 50 watts Class AB or 15 watts Class A. Volume is pretty much the same, but headroom is reduced. There's also less low end in Class A mode, but not by much. I assume the amp's ability to retain its low end is because Traynor use massive transformers.
Comment
Comment