SH-1 wiring mods - is this right for coil split/select?

[GuitarDoc]

Or you could just use Triple Shots. Keep it simple.

[piblock]

Since P/Ps are out, you could use a Freeway toggle switch to get those options + 2 more.

https://www.freewayswitch.com/products/

[68TwinReverb]

Cool. Hope you get it going. And don't forget that CTS makes those new low profile push-pulls. One of those might fit.

That's what I'm using. Still a little too big.

[ArtieToo]

Cool. Hope you get it going. And don't forget that CTS makes those new low profile push-pulls. One of those might fit.

[68TwinReverb]

Thanks everyone for the help.

Unfortunately, I've discovered that one of the two circuit boards inside the guitar for the piezo system is physically in the way of the DPDT volume pot. There is a notch in the board just large enough to accommodate the stock pot but not enough space for the added depth of the DPDT switch.

Coincidentally, the high E piezo sensor in the bridge is also acting up so I'm currently debating on whether to remove the entire piezo system altogether or to trouble shoot that further. Either way, will be a giant pain getting this back together.

[ArtieToo]

Not neat, but it works:

[ArtieToo]

Dang it! Reverse the two red wires on one of the switches. Doesn't matter which. I've got bridge red/white going to neck, and vice-versa.

[ArtieToo]

Like this:

[ArtieToo]

Since I can't edit that post, note also: you don't actually need to connect the green wires to that switch. Just take them direct to ground. Then also ground the bottom two terminals of that middle switch. Might make wiring inside the cavity easier.

[ArtieToo]

Did this quik-'n-dirty:

[beaubrummels]

Dangit. I think you're right. I've poured over this wiring for a few days now but didn't think about the grounds being connected at the PU selector.

I searched but couldn't find it - is there a way to have the switching options I want with 2 DPDT switches? Otherwise, I guess I'll have to make a decision on whether I want inner or outer coils. Could potentially add another DPDT switch as well since there is a "blend" pot on my guitar for a piezo pickup. I don't know the specs of that pot but its possible that I could find one with a DPDT option.

I did it with just push pulls in my Jackson. I basically made the two push pulls function like a triple shot. Vol up is the slug coil, tone up is the screw coil, and both up are the coils in parallel. Both down is normal humbucking. If you look for a P-Rail drawing using push pulls without triple shots, you'll see how to do it. Works with any 4-conductor humbuckers.

[skelt101]

It would slightly change the aesthetics, but you could just install a set of Triple Shot pickup rings…

[68TwinReverb]

Doesn't look right. You've got the hots and grounds permanently connected on the 3-way. Also, the coil select could only work if it were a 3-way on-on-on. As a push-pull on-on, you'll always either have one coil or ground out the pickups. You won't get any sound with that wiring.

Dangit. I think you're right. I've poured over this wiring for a few days now but didn't think about the grounds being connected at the PU selector.

I searched but couldn't find it - is there a way to have the switching options I want with 2 DPDT switches? Otherwise, I guess I'll have to make a decision on whether I want inner or outer coils. Could potentially add another DPDT switch as well since there is a "blend" pot on my guitar for a piezo pickup. I don't know the specs of that pot but its possible that I could find one with a DPDT option.

[beaubrummels]

Doesn't look right. You've got the hots and grounds permanently connected on the 3-way. Also, the coil select could only work if it were a 3-way on-on-on. As a push-pull on-on, you'll always either have one coil or ground out the pickups. You won't get any sound with that wiring.

[ThreeChordWonder]

Looks good to me...