Recent content by austin

Great pickup! I bought this to convert an HS Suhr T to an SS one. It originally came out of a Suhr Classic Antique T. However, it turns out I need a specially wound Classic T pickup to work with Suhr's quiet single coil system, so this is for sale. This measures 7.37 K on my meter and has 9" of...

Cool Rails Neck. Mounting tabs drilled out for direct mounting, 7" of wiring. $35 PayPal'd and shipped. SOLD! Hot Rails Neck. Mounting tabs drilled out for direct mounting, 9" of wiring. $35 PayPal'd and shipped. Thanks for looking. - Austin

SOLD! In great condition with 11" of wire. Yours for $50 PP'd and shipped. Thanks for looking. - Austin

Does anyone know if it's possible to use a 4-way switch in a Tele to give you the following combinations (the order is not important Neck w/volume and tone Neck w/volume (no tone) Neck and Bridge in Parallel w/ volume and tone Bridge w/ volume and tone Basically, the idea is to have one...

Has 7" of wire. $37.50 PayPal'd and shipped Thanks for looking. - Austin

Both of these pickups have had the mounting tabs drilled out for direct mounting! SOLD! Duncan JB, regular spaced, 10" wire. The baseplate and tabs have been snip-trimmed to get it to fit into a tight route. It was originally in the neck position, so if you want to put it there, you should have...

Mo Joe: 5" of wire, F-spaced. Came out of a Satriani sig guitar. $50 PayPal'd and shipped. SOLD! PAF Pro: 7" of wire. Note that the label says S1. That means it is a PAF Pro with chrome polepieces (as opposed to the usual black ones). $50 PayPal'd and shipped. Thanks for looking. - Austin

It there any easy way to pop out the brass threads on these so they can be direct-mounted. Usually, I can direct mounting these fine without doing anything, but for some reason, the builders of the particular guitar I want to put this in used the same screws that you would normally use in a...

A have Hamer Diablo II with a Jazz, JB and some sort of noiseless Dimarzio in the middle. The Dimarzio's a bit weak, so I was thinking of putting something else in there, preferably Duncan and noiseless. Any recommendations? - Austin

So I have a Jazz in the neck of one of my guitars and it's wired in the stock manner so that it splits to the stud (inside) coil. I'd like it to split to the outside coil instead. I know I could rewire it to do so, but would that then make it out of phase with the single coil in the middle...

$45 - Seymour Duncan Cools Rails Neck: Black, "new" form factor, 7" wire SOLD! - Dimarzio Tone Zone: Double black, F-Spaced, 5" wire. This was the stock bridge pickup in my 1996 Hamer Diablo II. The mounting tabs have been drilled out for direct mounting. SOLD! - Dimarzio N1: Double black...

I was drilling out a JB and Jazz set for direct-mounting using my hand drill. It took a long time; felt like a couple minutes per tab. Any chance I degaussed them while doing this? Doing the "pickups-as-refrigerator-magnet" suggests that the magnets aren't all that strong and the JB magnet is...

Pulled it out of a 1996 Hamer Diablo II. It has 5.5" of wire and the mounting tabs have been drilled out since it was direct-mounted. Yours for $45 PayPal'd and shipped. Thanks for looking. - Austin

I've used singlecoil-sized humbuckers in the past, but never in an actual strat. Right now I have an SSH strat and I'm considering throwing a singlecoil sized humbucker of some sort in the neck. Is it just a straight drop-in or will I need to fiddle around with the pots? It seems like it would...

Ended up going with a Custom (with an RCOUA5 magnet) instead. Has 11.5" of wire, so it would be great if you want to try a JB in the neck. Yours for $45 PayPal'd and shipped. Thanks for looking. - Austin