Recent content by Jack_TriPpEr

I am hoping to trade for a Dimarzio Area 61 or Area 58. Following are the pups I can offer in trade: Dimarzio Area 67 - used Dimarzio Bluesbucker, black - new in box Dimarzio Pro Track, black - new in box Dimarzio Cruiser Neck, black - new in box Dimarzio Super Distortion S - used I have...

I'm considering replacing the 25.5 scale, 21 fret neck on my Squier Strat with a 25.5 scale Warmoth neck that has the extension /overhang piece for up to 24 frets. Has anyone played one of these Warmoth necks with the 24 fret extension? My main question is, will the spacing on other frets...

First time shopping for a dummy coil. Please recommend some candidates I'll be using it wired to a Spin-A-Split control for use with a Fralin neck Jazzmaster pup, and a Fralin soapbar bridge P90 pup. I'd prefer tbe dummy coil to bein the footprint of a singlecoil pup, because I would like to...

The good insights about Jazzmaster guitars and pickups a few of you shared in Benjy_26's thread here: https://forum.seymourduncan.com/mobiquo/redirect.php?pid=6102759 ... has inspired an idea for a new project fot me: modify my cheap (but comfortable and well-playing) Squier Affinity Strat to...

This explanation from Robert Keeley about the difference btw a Limiter and a Compressor, helped me make a significant improvment in my tone when I discovered this video about three years ago. It lead to me incorporating a Limiter to even out the string-to-string volume in my clean tone and make...

Here's an SD diagram that features 1 tone pot. See the note that says the value of the capacitor needs to be 0.47uf, not the traditional 0.047uf.

This is it. I had downloaded it previously. Its not exactly as you describe. Position 2 is Neck Inner and Bridge Outer. And the reverse arrangement for Position 4. If you physically rotate the Neck pickup 180 degrees in its mounting ring, then you'll get Both Outers in Position 2 and Both...

"Just" Artie helped out with the wiring, huh?

https://www.rorguitars.com/products/expressiv-midi-pro

Referencing the attached diagram below: To get a tone pot dedicated to the Brudge pup, the wire labeled A gets connected to lug labeled 1 - as shown. After that, you have two options: 1. Connect the wire labeled B to lug labeled 3 - as shown, and you get no doubleloading in any of the 5...

I would like to replace the alnico 5 bar magnet under the rail coil of my Prail neck pup with a ceramic bar magnet to help boost the output volume of the rail coil. I see the Mojotone website carries a 2.35" size and a 2.60" size ceramic 8 bar magnet. Which of these is the size i need? Or do i...

My 2008 Ibanez ART400 is my favorite because it fits me like a glove, it's lightweight (just under 7.5 lbs), it sounds great and plays like butter. I believe it sits so well against me on a strap because of the combo of its tummy cut and the body thickness being on the thinner side: the body is...

The HSH diagram that BeauBrummels mentioned above, has 2 other errors besides how the 5 way switch's output is wired (covered in an earlier reply in this thread. That diagram is intended to split the neck and bridge at the same time using the push-pull switch but it has an error in that regard...

This morning when finishing the pack up, spotted this other craftsmanship/quality issue: the flame maple topin the upper horn had this small crack that was apparently allowed to remain unaddressed, and go through the stain and gloss coats processes.

Taking a 2nd look at it before I pack it up, there is some sgins of less-than-perfect worksmanship. Pics attached. 1. There are two small areas of bare wood on the seam of neck joint, in the lower horn. 2. The binding at the tip of the lower horn seems to have a stray paint/finish color mark...