Recent content by koshikas

Re: Can't get my killswitch right... i personally dont like the wiring in the above diagram. if the switch goes finicky you might endup with intermittent signal. its more like this with the two wires i mentioned drawn in red and orange;

Awesomeness. got pegasus swapped into one of my guitars, and bravo top notch job by Seymour Duncan for inventing one of the best pickups i've tried.

I'm wondering what would be the closest resembling single coil spaced pickup in the Duncan existing range that comes closest to a 'sentient' humbucker. just received a pegasus in delivery. (would be posting demos soon) I've already got rail humbucker in the neck of an SSH shredstick, barely...

interesting way of getting pickup positions warped https://www.kickstarter.com/projects/1165874210/the-pole-position-sliding-pickup-guitar

guys title says it all. i'll be pulling trigger on one of these later today. but as for now i'm feeling i'm not getting the complete picture yet. guitar is a shredstick (yamaha rgz-II) 6-string, basswood body, maple neck (bolt-on), rosewood finger board, floating trem. i feel it's mildly a...

Re: 50w Cab and 100w Head did bit of search for guides didnt find any. but this is a very simple mod. first things first; 1) does your amp head have a 4 ohm speaker out. 2) do you value the cab so much that altering it might ruin its value. (you'll need to drill a hole or two in the back...

Re: 50w Cab and 100w Head meaning that the two 8 ohmer greenbacks are in series, making the total impedance 16 ohms. solution (1); if you can put a 16 ohm power resistor (with 100W rating) in parallel with the cab you endup having total impedance of 8 ohms and the whole thing capable of...

after many teasers, it is finally coming http://geargods.net/news/fractal-audio-teases-something-maybe-a-floor-axe-fx/

Hello there, need to get one of my guitars neck shimmed. i've been playing the guitar with bit of moderate action from the time i bought it. but now realize that it ought to be a shredstick, which it is. so need to get that action crazy low if i can. the floating trem bridge is at its lowest the...

I have J-Bass copy (fret-less) that I think is not having its pickup setup correctly. I'm beginner in bass and got little to no idea on what to do. this is a cheap beginner bass, so I'm assuming it's having ceramic j-style pickups. I'm hoping to get good output because when I dig too much, I end...

guys I'm convinced that Ibanez has put pickups in wrong positions in my 'musician'. as it is, bridge reads 7.1k and neck reads 7.5k. neck sounds awful muddy as it is and I was only able to get decent highs only after removing all screw poles. bridge is nice open and bright but feels wimpy when...

what do you call a dead note on a guitar. I have a shred stick which I think has a dead note and also has a fret-less bass that definitely has a few. the one in the shred stick is weird. under gain when I let the note sustain, it goes into feedback more or so instantly. then the note dies as...

Joe Bonamassa’s 5 Most Underrated Amps click here

Re: Single coil modding i m wondering whether u got this right; see bar magnets for humbuckers have different magnetic orientation to those ceramic bar magnets u get on cheap single coils. so u might be having a weak magnetic field if the magnetic field (poles) are perpendicular and not...

Re: Dummy Load Products/8/16 ohm Head With Two 8 ohm Cabinents u ll need somethin created like this; all u need is 3 T-S sockets, and power wire. make note of how the tip/sleeve connections are made, or else u will end up with out-of-phase cabinets. couldnt get hold of anythin on web, so...