Recent content by Mephis

http://www.soundclick.com/bands/songInfo.cfm?bandID=685825&songID=5774047 Using my Kramer with a Screamin Demon on the rhythm. Using my Ibanez with a MegaDrive on the lead. I have the lead set back in the track on purpose.

I bought it awhile back for use in my carvin, then swaped it out for a double whammy about a week later. It's pretty much in new condition since I only had it out of the box for a week. Leads are at full length, just the ends are stripped. Resistance is 16.53k. Four conductor. Only thing is...

Seymour duncan SH-8 invader: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=270142729069 Starting bid: $49.99 I will not pull the auction for selling outside of ebay. Digitech RP200A Effects processor: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=270142725562 Starting bid: $60 BIN...

Well since this is pretty much the tech/wiring side of the forums I figured my question would be best addressed here. Here's what I have I have a Megadrive/Air norton combo in it that I just installed today. The neck-series position is not working, it has ultra low output. I'm guessing...

Old DMZ pickups interest me after having great sucess with a double whammy. I love my double whammy very much in my carvin but I'm trying to think of what I want in this ibanez. The stock pickups are great but I like trying different stuff. The ibanez is neck-thru maple/walnut 5 piece with...

I have it listed on ebay, if you're interested, check it out: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=270125102814

I'm looking at one on ebay. I'm wanting to unload my gibson and get another super strat. I'm especially interested in ibanez. Only reason I'm even asking about it is due to the fact that my RG350DX was a total heap and I'm waiting to know how the RGT42 would be. I know it's korean, but I...

So I bought some GT tubes since one of the tubes in my 6505+ was pretty much shot, all the pins feel like they're about to fall out. Anyway, I went to guitar center and they wanted nearly $200 for a quad and I told them no way. They sold me 2 duets with the same power rating for $50. I just...

I'm considering trading my AD30VT in on one since I can't stand it. I figure it would make a nice practice/recording amp and something that would be nice for actually being able to take some where. Maybe even a good amp to mod. Anyone tried one? Opinions; comments?

Got bored with never being able to use the guitar much due to feedback. The stock single in the bridge registered around 13k and sounded like a P-90 with a little more beef. Sure it was a great pickup, but it squeeled horribly bad. I decided to buy a RIC humbucker from www.pickofthericks.com...

I had long thought it to be a JB. It had a sort of harsh edge (Leads were scratchy sounding) to it and it didn't sound very strong. It was very grindy also. It came out of my kramer beretta. But I put it on the tester and it shows 13.73k! That certantly can't be a JB. Then I tested the coils...

My guitar teacher is selling an afterburner cheap and I really have no use for the coil splitter on my carvin. But I don't want to leave the hole empty or with a crappy plug. Would I be insane to have an afterburner with an invader? This is purely in concept because I feel a coil split on...

I spent the better part of 7 hours exchanging a pickup, buying pickups, driving, installing, completely re-wiring 6 times due to cold solder joints, and re-stringing. But I'm finally done!!! :dance: Invader bridge, duncan design scorcher middle, and stock A2 single coil in the neck. Great...

Never mind, dead pickup. This is try no.3. I can not wire the pickup in series with my mini switch. I'm trying to wire it like the old carvin pickup is. (To be able to split using the toggle) (Bottom row= Hot - Hot out to switch - Black/White coil wires) Green and bare wires solders to...

Carvin custom shop kit. Alder body (Swamp ash with an ebony board might have been to bright for me.) I'm amazed at how fast this went together. It took me around 15 minutes to put it together once I was done with the finishing process... Everything fits very tight and snug and goes together...