I have a set of Lace Hemi Humbuckers a Fender Super 5 way switch 1 Vol and 1 Tone and want to wire them like this HN, Outer Coils, HH, Inner Coils, HB. The pickups are really like 4 single coil pickups mounted on two so they look like humbuckers 2 starts 2 finishes 2 grounds. I have tried every diagram I could find on the internet including the six at guitarelectronics.com. I have spent about 13 hours wiring, triple checking my work and rewiring but all diagrams I have found are flawed in some way positions not working ect. The color code is N start Orange, N finish White, S start Orange/black, S finish White/black. the grounds are both green. Any help would be greatly appreciated.
Announcement
Collapse
No announcement yet.
5 way super switch and 4 pickups
Collapse
X
-
EHD
Just here surfing Guitar Pron
RG2EX1 w/ SD hot-rodded pickups / RG4EXFM1 w/ Carvin S22j/b + FVN middle
SR500 / Martin 000CE-1/Epiphone Hummingbird
Epiphone Florentine with OEM Probuckers
Ehdwuld branded Blue semi hollow custom with JB/Jazz
Reptile Green Gibson Custom Studio / Aqua Dean Shire semi hollow with piezo
Carvin Belair / Laney GC80A Acoustic Amp (a gift from Guitar Player Mag)
GNX3000 (yea I'm a modeler)
-
Re: 5 way super switch and 4 pickups
hang onEHD
Just here surfing Guitar Pron
RG2EX1 w/ SD hot-rodded pickups / RG4EXFM1 w/ Carvin S22j/b + FVN middle
SR500 / Martin 000CE-1/Epiphone Hummingbird
Epiphone Florentine with OEM Probuckers
Ehdwuld branded Blue semi hollow custom with JB/Jazz
Reptile Green Gibson Custom Studio / Aqua Dean Shire semi hollow with piezo
Carvin Belair / Laney GC80A Acoustic Amp (a gift from Guitar Player Mag)
GNX3000 (yea I'm a modeler)
Comment
-
Re: 5 way super switch and 4 pickups
black wire become orange
Green/bare becomes whiteblack/green
red/white become white/orangeblack
1) remove that jumper
separates the top and bottom rows
2) hot from volume to top row ( dotted line )
makes top row for outer coils
3) move split function pair from position 4 to position 2
as your lace arent layed out like the seymours this will align the outer coils
together
4)ignore 4 I dont know what i was pointing at
DOH!!
5) make jumper from bottom row position 2 to top row position 4 >dark purple
6) make jumper from bottom row position 4 to top row position 2 >lighter purple
these purple jumpers will cross and align the inner coils in position 2
let me know what happens
you may have to swap hot and ground on the right commons
as I may have got inner and outer mixed upEHD
Just here surfing Guitar Pron
RG2EX1 w/ SD hot-rodded pickups / RG4EXFM1 w/ Carvin S22j/b + FVN middle
SR500 / Martin 000CE-1/Epiphone Hummingbird
Epiphone Florentine with OEM Probuckers
Ehdwuld branded Blue semi hollow custom with JB/Jazz
Reptile Green Gibson Custom Studio / Aqua Dean Shire semi hollow with piezo
Carvin Belair / Laney GC80A Acoustic Amp (a gift from Guitar Player Mag)
GNX3000 (yea I'm a modeler)
Comment
-
Re: 5 way super switch and 4 pickups
Thanks ehdwuld. I'll try it.Last edited by method1979; 06-02-2010, 09:19 AM.
Comment
-
Re: 5 way super switch and 4 pickups
could try this from the Dimarzio site
Two Humbuckers with Multipole 5-way Switch EP1112
Introduction:
This diagram provides the three classic humbucker sounds: neck (position 1), neck & bridge
(position 3) and bridge (position 5), with the addition of two "Fender-like" sounds: a Tele-like
tone with the outside coils in parallel (position 2) and a Strat-like tone with the inside coils in
parallel (position 4). All five positions are hum canceling. Because the 2 and 4 positions select
single coils from each pickup and connect them in parallel, they will have less volume than posi-
tions 1, 3 and 5, which select coils wired in series. The amount of volume-drop in positions 2 and 4
will depend on the specific pickup models that are installed.
Technical notes:
A standard 5-way switch does not have the capability to get these combinations. The switch -
shown in the diagram is a multipole switch (DiMarzio EP1112). There are many other 2 hum-
bucker variations possible with this type of switch. Resistance value of the controls is a matter of
taste, but 500 Kohm is a good starting point for most pickup combinations and .022 μfd is the
basic recommended value for the tone control capacitor.
Diagram notes: White wires are rendered in light gray.
EDIT
you waould have to translate the dimarzio wiring to your Lace
Dimarzio RED = Lace ORANGE
Dimarzio BLACK = Lace WHITE
Dimarzio WHITE = Lace ORANGEBLACK
Dimarzio GREEN = Lace WHITEBLACK
EHD
Just here surfing Guitar Pron
RG2EX1 w/ SD hot-rodded pickups / RG4EXFM1 w/ Carvin S22j/b + FVN middle
SR500 / Martin 000CE-1/Epiphone Hummingbird
Epiphone Florentine with OEM Probuckers
Ehdwuld branded Blue semi hollow custom with JB/Jazz
Reptile Green Gibson Custom Studio / Aqua Dean Shire semi hollow with piezo
Carvin Belair / Laney GC80A Acoustic Amp (a gift from Guitar Player Mag)
GNX3000 (yea I'm a modeler)
Comment
Comment