Page 1 of 2 12 LastLast
Results 1 to 20 of 24

Thread: Fret leveling vs neck quality.

  1. #1
    Senior Member
    Join Date
    May 2019
    Posts
    70

    Default Fret leveling vs neck quality.

    Hi.

    To what extent can a good fret leveling job get you crazy low action?

    I've done fret leveling jobs on two guitars with relative succes, but was not able to get the crazy low action I have on my Korean Michael kelly Patriot Shadow, which simply has a $3000 guitar neck.
    One of the guitars I worked on was also a Michael kelly Patriot (albeit an Indonesian one).

    I'm thinking that the leveling is done when the neck is straight, but I figure restrung, a good neck will make a perfect bow, allowing for very low action, while a lesser neck's bow may not be smooth (a bit bumpy let's say) and 'cause fret buzz anyway?
    Or is it just a matter of inadequate skills?

  2. #2
    A Ficus ehdwuld's Avatar
    Join Date
    Sep 2009
    Location
    South Alabama
    Posts
    10,251

    Default Re: Fret leveling vs neck quality.

    Well if the neck is straight
    And the frets are level
    And the nut is cut correctly
    And the neck angle.is good
    And the bridge saddles are just right

    And if with all this
    The neck isn't twisted

    I think you should be able to get it super low

    Its easier to get super low action
    With taller frets
    Or at least that's what my understanding is
    EHD
    Just here surfing Guitar Pron
    RG2EX1 w/ SD hot-rodded pickups / RG4EXFM1 w/ Carvin S22j/b + FVN middle
    SR500 / Martin 000CE-1/Epiphone Hummingbird
    Epiphone Florentine with OEM Probuckers
    Ehdwuld branded Blue semi hollow custom with JB/Jazz
    Reptile Green Gibson Custom Studio / Aqua Dean Shire semi hollow with piezo
    Carvin Belair / Laney GC80A Acoustic Amp (a gift from Guitar Player Mag)
    GNX3000 (yea I'm a modeler)

  3. #3
    Ultimate Tone Slacker ICTGoober's Avatar
    Join Date
    Oct 2016
    Location
    Wichita, KS
    Age
    63
    Posts
    2,717

    Default Re: Fret leveling vs neck quality.

    Fret height has nothing to do with low action.

    As for OP, you're probably doing it wrong.

  4. #4
    A Ficus ehdwuld's Avatar
    Join Date
    Sep 2009
    Location
    South Alabama
    Posts
    10,251

    Default Re: Fret leveling vs neck quality.

    Quote Originally Posted by ICTGoober View Post
    Fret height has nothing to do with low action.

    As for OP, you're probably doing it wrong.
    Helpful much

    Thanks Goob
    EHD
    Just here surfing Guitar Pron
    RG2EX1 w/ SD hot-rodded pickups / RG4EXFM1 w/ Carvin S22j/b + FVN middle
    SR500 / Martin 000CE-1/Epiphone Hummingbird
    Epiphone Florentine with OEM Probuckers
    Ehdwuld branded Blue semi hollow custom with JB/Jazz
    Reptile Green Gibson Custom Studio / Aqua Dean Shire semi hollow with piezo
    Carvin Belair / Laney GC80A Acoustic Amp (a gift from Guitar Player Mag)
    GNX3000 (yea I'm a modeler)

  5. #5
    OH THE GLAZE! Clint 55's Avatar
    Join Date
    Aug 2016
    Location
    Santa Fe
    Posts
    7,912

    Default Re: Fret leveling vs neck quality.

    It has to do with set up and level frets either from a good fret job or a well produced neck maybe run through a fret machine. That's it. "Quality" doesn't really have much to do with it. Almost all production guitars just have the frets installed without a level.
    Last edited by Clint 55; 02-02-2020 at 03:24 PM.
    In a fast german car
    I'm amazed that I survived
    An airbag saved my life

  6. #6
    A Ficus ehdwuld's Avatar
    Join Date
    Sep 2009
    Location
    South Alabama
    Posts
    10,251

    Default Re: Fret leveling vs neck quality.

    Truss rod can correct for most any bow in the neck

    Not a twist

    Bow
    EHD
    Just here surfing Guitar Pron
    RG2EX1 w/ SD hot-rodded pickups / RG4EXFM1 w/ Carvin S22j/b + FVN middle
    SR500 / Martin 000CE-1/Epiphone Hummingbird
    Epiphone Florentine with OEM Probuckers
    Ehdwuld branded Blue semi hollow custom with JB/Jazz
    Reptile Green Gibson Custom Studio / Aqua Dean Shire semi hollow with piezo
    Carvin Belair / Laney GC80A Acoustic Amp (a gift from Guitar Player Mag)
    GNX3000 (yea I'm a modeler)

  7. #7
    Bacteriaolgoist GuitarDoc's Avatar
    Join Date
    May 2007
    Location
    Calif
    Age
    72
    Posts
    13,835

    Default Re: Fret leveling vs neck quality.

    Quote Originally Posted by ehdwuld View Post
    Truss rod can correct for most any bow in the neck

    Not a twist

    Bow
    Unless you have a neck with double truss rods.
    Originally Posted by IanBallard
    Rule of thumb... the more pot you have, the better your tone.

  8. #8
    Mojo's Minions
    Join Date
    Mar 2008
    Location
    The Hague, Netherlands
    Posts
    3,354

    Default Re: Fret leveling vs neck quality.

    Quote Originally Posted by GuitarDoc View Post
    Unless you have a neck with double truss rods.
    and that is rare. Very rare. I only know of a few Rickenbackers who do it that way?

  9. #9
    Super Toneologist DavidRavenMoon's Avatar
    Join Date
    Apr 2006
    Posts
    1,466

    Default Re: Fret leveling vs neck quality.

    I once had a customer with a brand new American Standard Strat. The action was low, but he wanted it lower.

    Leveling the frets helped a lot but he wanted it lower. So I removed the frets and leveled the board and installed new frets.

    It was so low he asked me to raise it!

    But fret leveling helps.


    Sent from my iPhone using Tapatalk

  10. #10
    Bacteriaolgoist GuitarDoc's Avatar
    Join Date
    May 2007
    Location
    Calif
    Age
    72
    Posts
    13,835

    Default Re: Fret leveling vs neck quality.

    Quote Originally Posted by orpheo View Post
    and that is rare. Very rare. I only know of a few Rickenbackers who do it that way?
    Yeah, me too.
    Originally Posted by IanBallard
    Rule of thumb... the more pot you have, the better your tone.

  11. #11
    Super Toneologist vinta9e's Avatar
    Join Date
    Jan 2013
    Posts
    1,268

    Default Re: Fret leveling vs neck quality.

    Quote Originally Posted by WDeeGee View Post
    a good neck will make a perfect bow, allowing for very low action, while a lesser neck's bow may not be smooth (a bit bumpy let's say) and 'cause fret buzz anyway?
    Or is it just a matter of inadequate skills?
    One will make a pefect bow by itself, another one must be helped. Bumpy fretboards can be sanded to some extent. Bumpy fretwork can be redone. From that point on, it's all a matter of how accurately you can assess the situation and how much skill you have in executing the correction, assuming your judgment was correct in the first place...

    IOW, sanding a badly seated fret sounds like pointless work.

  12. #12
    Mojo's Minions LLL's Avatar
    Join Date
    Oct 2014
    Location
    Evil Volcano Lair
    Age
    51
    Posts
    3,575

    Default Re: Fret leveling vs neck quality.

    Super low action is over-rated.

    Raise the action until each note rings clear and the strings have a little "bounce" to them.
    Lefty Lounge Lizard's Guitars & Amps Extravaganza



    Fastest ears in the West

    DIY or go home.

    My Soundcloud

  13. #13
    Bacteriaolgoist GuitarDoc's Avatar
    Join Date
    May 2007
    Location
    Calif
    Age
    72
    Posts
    13,835

    Default Re: Fret leveling vs neck quality.

    Quote Originally Posted by LLL View Post
    Super low action is over-rated.
    Only if you pound your strings like a 13 year old beginner trying to play metal.
    Originally Posted by IanBallard
    Rule of thumb... the more pot you have, the better your tone.

  14. #14
    Mojo's Minions LLL's Avatar
    Join Date
    Oct 2014
    Location
    Evil Volcano Lair
    Age
    51
    Posts
    3,575

    Default Re: Fret leveling vs neck quality.

    Quote Originally Posted by GuitarDoc View Post
    Only if you pound your strings like a 13 year old beginner trying to play metal.
    Higher action (but not too high) makes the strings livelier, facilitates better bending and vibrato, and cleaner notes.

    Besides that, you can pick as "delicately" as you want regardless of how high/low the action is.
    Lefty Lounge Lizard's Guitars & Amps Extravaganza



    Fastest ears in the West

    DIY or go home.

    My Soundcloud

  15. #15
    Bacteriaolgoist GuitarDoc's Avatar
    Join Date
    May 2007
    Location
    Calif
    Age
    72
    Posts
    13,835

    Default Re: Fret leveling vs neck quality.

    "Higher" only helps if the existing action is so low that the strings are buzzing on the frets. If they're not buzzing, then raising the height of the strings makes no difference.

    Bending and vibrato are facilitated by the height of the frets. That's also why some players like scalloped fretboards (simulates very high frets)
    .
    Originally Posted by IanBallard
    Rule of thumb... the more pot you have, the better your tone.

  16. #16
    Ultimate Tone Slacker
    Join Date
    May 2004
    Location
    Dateing your cougar aunt
    Posts
    2,455

    Default Re: Fret leveling vs neck quality.

    Quote Originally Posted by LLL View Post
    Higher action (but not too high) makes the strings livelier, facilitates better bending and vibrato, and cleaner notes.

    Besides that, you can pick as "delicately" as you want regardless of how high/low the action is.
    many claim higher action gives better sustain. I like slightly lower action then factory settings. but ya, when I bend I dont like uber low action. I also like my action not too low for the sake of tapping or harmonics. I seem to do better tapping harmonics on strings that are not too low. it seems the harmonics ring better or clearer

  17. #17
    Chris JB_From_Hell's Avatar
    Join Date
    May 2004
    Location
    Yellow Springs, Ohio
    Age
    40
    Posts
    19,364

    Default Re: Fret leveling vs neck quality.

    I like higher action on a guitar, and lower on a bass. Probably because I bend strings like crazy on guitar, and if they’re too low, they adjacent string gets caught under my fingers.

    On a bass, I’m more into sliding than bending. I also like a little buzz on bass if I dig in hard. On guitar, it sounds like crap.

  18. #18
    OH THE GLAZE! Clint 55's Avatar
    Join Date
    Aug 2016
    Location
    Santa Fe
    Posts
    7,912

    Default Re: Fret leveling vs neck quality.

    Quote Originally Posted by GuitarDoc View Post
    "Higher" only helps if the existing action is so low that the strings are buzzing on the frets. If they're not buzzing, then raising the height of the strings makes no difference.
    Higher action makes the notes more punchy.
    In a fast german car
    I'm amazed that I survived
    An airbag saved my life

  19. #19
    OH THE GLAZE! Clint 55's Avatar
    Join Date
    Aug 2016
    Location
    Santa Fe
    Posts
    7,912

    Default Re: Fret leveling vs neck quality.

    My fret leveling assault. Each grit will take out the scratches from the previous grit. Radius block with 60 to level. Crown with the 150 and 300 grit crowning files. Quarter round file for the ends. 220, 320, 800, 1500 sandpaper.

    Click image for larger version. 

Name:	20200214_132842.jpg 
Views:	15 
Size:	83.5 KB 
ID:	103315
    Last edited by Clint 55; 02-14-2020 at 01:39 PM.
    In a fast german car
    I'm amazed that I survived
    An airbag saved my life

  20. #20
    OH THE GLAZE! Clint 55's Avatar
    Join Date
    Aug 2016
    Location
    Santa Fe
    Posts
    7,912

    Default Re: Fret leveling vs neck quality.

    Click image for larger version. 

Name:	level.jpg 
Views:	8 
Size:	80.8 KB 
ID:	103316

    Click image for larger version. 

Name:	level2.jpg 
Views:	9 
Size:	52.9 KB 
ID:	103317
    In a fast german car
    I'm amazed that I survived
    An airbag saved my life

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •