Single-coil pups and misc. 4 sale or trade

[metalchurch79]

I have (2) DiMarzio FS-1's (DP-110) 2 conductor wiring w/ about 5 inches of lead $37.00 shipped

I have (2) Seymour Duncan Designed SC-101's like new condition (out of a Jackson DK2) I think they have a 4 conductor wiring w/ about 7 inches of lead wire. $25.00 shipped

*[ Your choice of White or Black covers, I also have (1) brand new Red cover that's a stray]

(1) EMG Select SES - 2 conductor wiring w/ about 4-5 inches of lead wire. Used but decent condition. $8.00 shipped

(3) Groove Tube 12AX7's only a few months old. I had them in my Engl preamp and replaced them w/ Tung-Sol's
$20.00 shipped

I have some more 12AT7's and AX7's so I'll check to see and update if necessary.


If anyone is interested post here, or pm me and we'll go from there.
I will accept trades as well.

NO paypal.
US Postal Money Order, Check, or Cash only

My USB port or the USB cable for my camera is messed up and I cant post pictures. I'm tryin to figure out whats up with it.

Thanks
-Joe

 

[metalchurch79]

Re: Single-coil pups and misc. 4 sale or trade

Ok I found my other box of tubes
Heres what I got:

These were out of my Marshall 9200 Poweramp and they work perfectly
(1) Marshall 12AT7
(1) Marshall 12AX7

(1) Chinese(???-no name) 12AX7-A
(1) Chinese(???-no name) 12AX7-A
(1) Groove Tube 12AT7 (ECC81/6021)
(1) Sovtek 12AX7 (7025/12AX7WB)
(1) No name 12AX7 (ECC83M)

Also I have (4) matched quad Made In Russia 5881's I think they are Sovteks actually. These were out of my Marshall 9200 Poweramp as well and they worked fine, but I dont know how old they are or anything like that.
I owned the Marshall since September of '07 and the tubes were replaced in June of '08.

Like I said, I dont really know what to ask for the tubes really, so I'll be more than fair about the price/and or trade value.

All of these tubes do work and they work fine.
The 12AT & AX7's were just swapped back and forth in my preamp about 4 weeks ago, so I know they work for sure.


I'll try to get some pictures up for you guys.

 

[metalchurch79]

Re: Single-coil pups and misc. 4 sale or trade

I also have a brand new Liscensed Floyd in Black.
Comes with everything needed for install.
Has the 32mm short block for a recessed trem cavity, but it can be upgraded to a long-block 42mm if needed.
$35.00 shipped

I have 4 brand new metal humbucker rings in Black.
They are 1/8" and have flat bottoms.
Can be stacked to get 1/4" for the bridge position, and they actually look good like that.
There's no comparison how much better they look over plastic...
$10 for all 4 of them.

Most everything else is still available except for some of the Groove Tube 12AX7's and AT7's..

Thanks

 

[metalchurch79]

Re: Single-coil pups and misc. 4 sale or trade

Metal pickup rings are pending sale.
Most everything else still available for sale or trade.

Thanks for looking guys!

 

[metalchurch79]

Re: Single-coil pups and misc. 4 sale or trade

The pickup rings are sold. The GrooveTubes are also gone.

As of now most everything else is still available.

Thanks
-Joe

 

[metalchurch79]

Re: Single-coil pups and misc. 4 sale or trade

Here's some pictures, sorry for the delay. Anyone interested pm me with any questions, or trade offers.
DiMarzio FS-1's (DP-110)
(front)

(rear)


Seymour Duncan Designed SC-101's
(Red & White)
EMG Select SES
(black)



Licensed Floyd:

 

[metalchurch79]

Re: Single-coil pups and misc. 4 sale or trade

All prices are negotiable, and I'm open for trades as well.
Here's a few things that I'm looking for:


DiMarzio Distortion "F" spaced in Creme for a Dave Murray Strat that I'm building, so if anyone has one of those and would consider a partial trade for anything I have listed, let me know.

I'd also consider swapping all of this stuff for either the pickup listed above or a Creme F spaced Breed, EVO2 or Evolution. Condition doesn't matter much.
Thank you for checking this out.
-Joe