HSS guitar: new Ibanez dyna-MIX9 switching

[Mincer]

So I did this and found that position 2 in the "Tap Mode" sounded out of phase. Looking at the diagram, the series link is sent to ground but this turns off the bottom coil. I did a little change to the schematic to fix it. Thanks for sharing this, it was greatly helpful.

Welcome to the forum, and thank you for adding to our knowledge here!

[CheoMoralesGuitarist]

Re: HSS guitar: new Ibanez dyna-MIX9 switching

It works in the guitar I have put together.
I have drawn the complete wiring diagram for those who are interested:
[ATTACH=CONFIG]90588[/ATTACH]

So I did this and found that position 2 in the "Tap Mode" sounded out of phase. Looking at the diagram, the series link is sent to ground but this turns off the bottom coil. I did a little change to the schematic to fix it. Thanks for sharing this, it was greatly helpful.

[ICTUS_MEDICAL]

Why a 3PDT mini switch? A DPDT is enough...

[tumad]

I wonder if someone could help me.
I want to remove completely the dyna switch as I dont use it at all but want that switch to rather split to the bridge coil and position 4 to be middle and bridge coil similar to a HSS strat. Those are the only combos I need. I hope the pic below helps. So bridge position switch down is humbucker, switch up is split to the coil nearest the humbucker. Position 4 is middle and humbucker bridge coil as per SSS.
many thanks everyone

[Juanhanglo]

Re: HSS guitar: new Ibanez dyna-MIX9 switching

why not this?

https://www.freewayswitch.com/schematics-blade/

the 2x5 way blade does just what you want, it solders easily, super sturdy mechanism, and no extra toggle you need to have. I know what I'd want on my HSS guitar.

These switches are great! They are super high quality.

I used the 3/6 way tele version in my strat.
N, n/b, b on bank 1
b/m, m, b/m on bank 2.

Using 1 switch to access 10 different sounds on a strat or superstrat makes stage switching a breeze.

[DGSEY]

After success with rewiring the HSS AZ224 switching to another guitar (thanks to you guys!), did anyone work out the Ibanez H H AZ242 switching ?

[DGSEY]

Re: HSS guitar: new Ibanez dyna-MIX9 switching

It works in the guitar I have put together.
I have drawn the complete wiring diagram for those who are interested:
[ATTACH=CONFIG]90588[/ATTACH]

===============================
Big thanks for this, I've completed the rewiring in a HSS guitar and it works great. cheers!

[DGSEY]

Re: HSS guitar: new Ibanez dyna-MIX9 switching

[ATTACH=CONFIG]88101[/ATTACH]

- 5-Way Super Switch
- 3PDT toggle

Humbucker uses Duncan colors (black to hot, red/white for splitting, green and bare to ground)

Hot goes to your volume control. GND is ground.

======================
Big thanks for this, I've completed the rewiring in a HSS guitar and it works great. cheers!

[TonyStarkBra]

Re: HSS guitar: new Ibanez dyna-MIX9 switching

It works in the guitar I have put together.
I have drawn the complete wiring diagram for those who are interested:
[ATTACH=CONFIG]90588[/ATTACH]

I have been looking for this scheme in many places, thank you very much!
The scheme requires a 3PDT switch, but I am quite adamant to make another hole in the guitar shield to install a switch, I saw in this video the same system using a push-pull: (7) 9 TONES IN A STRATOCASTER GUITAR | dyna-MIX9 switching system w/Push Pull - YouTube
I did not find a potenciometer with a push-pull 3PDT, only DPDT...
how to use this scheme using a push-pull?

[ArtieToo]

Re: HSS guitar: new Ibanez dyna-MIX9 switching

Because the neck & middle "hots" go to different positions on the Superswitch. They need independent functionality for that switching scheme to work.

[orpheo]

Re: HSS guitar: new Ibanez dyna-MIX9 switching

That would be really difficult, if not impossible, because the neck/middle are sometimes in series. That complicates things. Maybe one of the younger guru's will chime in.

why wouldn't it work if I run each hot signal from mid and neck through a pot first? I'm not seeing why that can't work but then again, I'm not that much of a wiring buff. I can think up crazy stuff but can't design it haha

[ArtieToo]

Re: HSS guitar: new Ibanez dyna-MIX9 switching

BUMP.

Is it possible to have this wiring with volume pots for mid+neck and bridge?

That would be really difficult, if not impossible, because the neck/middle are sometimes in series. That complicates things. Maybe one of the younger guru's will chime in.

[orpheo]

Re: HSS guitar: new Ibanez dyna-MIX9 switching

BUMP.

Is it possible to have this wiring with volumepots for mid+neck and bridge?

[orpheo]

Re: HSS guitar: new Ibanez dyna-MIX9 switching

The thing is, I've got this crazy notion that I want this in an HSS LP as well as an HH LP where I use the two coils of the neck humbucker as if it's two singlecoils. four pots, 1 push pull, 5 way blade and we're off. And yes, I have a 500K 4 pole pushpull pot

[orpheo]

Re: HSS guitar: new Ibanez dyna-MIX9 switching

THANKS! Looks/sounds like a plan.

One final question.

I want individual volume/tone controls; 1 set for the bridge and 1 set for the neck/middle combination.

Can that be done? I do have a few 500K dual gang pots laying around, if that helps.