EMG Pickup connectors
- Thread starter AniML
- Start date
Zerberus
Baron Von Shred
Re: EMG Pickup connectors
Good question.....the connector is essentially identical to the ones on many internal USB devices for PCs.... Comp USA or Radio Shack might be a good place to start...
EMG calls the system "QuickConnect".... What I´m wondering though is what you plan on doing, as the EMG electronics aren´t really compatible with any passive PUs.....
Good question.....the connector is essentially identical to the ones on many internal USB devices for PCs.... Comp USA or Radio Shack might be a good place to start...
EMG calls the system "QuickConnect".... What I´m wondering though is what you plan on doing, as the EMG electronics aren´t really compatible with any passive PUs.....
AniML
New member
Re: EMG Pickup connectors
I want to fit something similar onto my own pickups so I can swap them without desoldering and resoldering. I would cut my pickup leads to around 3-4 inches and solder in a male connector and put the female in the pup cavity.
The best thing I had found so far was a 5 pin mini DIN, but that might be too tight of a fit in the pup cavity.
USB... Hmmmm
Zerberus said:Good question.....the connector is essentially identical to the ones on many internal USB devices for PCs.... Comp USA or Radio Shack might be a good place to start...
EMG calls the system "QuickConnect".... What I´m wondering though is what you plan on doing, as the EMG electronics aren´t really compatible with any passive PUs.....
I want to fit something similar onto my own pickups so I can swap them without desoldering and resoldering. I would cut my pickup leads to around 3-4 inches and solder in a male connector and put the female in the pup cavity.
The best thing I had found so far was a 5 pin mini DIN, but that might be too tight of a fit in the pup cavity.
USB... Hmmmm
AniML
New member
Re: EMG Pickup connectors
I just wish I could find them. I've been to 3 Radio Shacks. None have anything small enough. Any of the industrial sites (Mouser, etc) I've found either do not show images of the items or only sell in quantity. If I could just find a female shell similar to EMG's and a male harness /connector I'd build it. Can you point me in the right direction?
thx
Zerberus said:If you´re just wanting to do something similar, ther is a plethora of small-scale electronics connectors you could use... Radio Shack
I just wish I could find them. I've been to 3 Radio Shacks. None have anything small enough. Any of the industrial sites (Mouser, etc) I've found either do not show images of the items or only sell in quantity. If I could just find a female shell similar to EMG's and a male harness /connector I'd build it. Can you point me in the right direction?
thx
Zerberus
Baron Von Shred
Re: EMG Pickup connectors
I wish I could.. I get small electronics parts from a local specialty dealer (essentially Sadio Shack, lol), and figured your chances would be best there.....
Though what you could also try are the "bullet" connectors often used in older cars.... or battery connectors for an R/C car, maybe....
I wish I could.. I get small electronics parts from a local specialty dealer (essentially Sadio Shack, lol), and figured your chances would be best there.....
Though what you could also try are the "bullet" connectors often used in older cars.... or battery connectors for an R/C car, maybe....
itbepopples
New member
Re: EMG Pickup connectors
If you're going to go the connector route make sure you buy a can of contact cleaner to go with it. That stuff works so well I still almost don't believe it. It worked getting the road salt off of several abused bare connector ends/wires connecting a salt spreader to a truck wiring harness at work; which was really causing problems come snow time. If it worked well for that and cleaning potentiometers I can't imagine there would be any signal degradation compared to soldered connections...as long as you gave em a spray every now and again.
If you're going to go the connector route make sure you buy a can of contact cleaner to go with it. That stuff works so well I still almost don't believe it. It worked getting the road salt off of several abused bare connector ends/wires connecting a salt spreader to a truck wiring harness at work; which was really causing problems come snow time. If it worked well for that and cleaning potentiometers I can't imagine there would be any signal degradation compared to soldered connections...as long as you gave em a spray every now and again.
3th3r
New member
Re: EMG Pickup connectors
If you can't find these 5-pin connectors (they're not that uncommon) at your local electronics store, you can always order a cable like this one and use the connectors:
http://www.frontx.com/cpx512.html
If you can't find these 5-pin connectors (they're not that uncommon) at your local electronics store, you can always order a cable like this one and use the connectors:
http://www.frontx.com/cpx512.html
AniML
New member
Re: EMG Pickup connectors
If you are referrring to the cable 3th3r directed me to, I would remove the connectors from the provided cable, solder one connector to the pickup end of the lead and the other to the guitar side of the wiring. In otherwords, it would be spliced into the pickup wire within the pickup cavity.
Fusion1 said:
If you are referrring to the cable 3th3r directed me to, I would remove the connectors from the provided cable, solder one connector to the pickup end of the lead and the other to the guitar side of the wiring. In otherwords, it would be spliced into the pickup wire within the pickup cavity.
Similar threads
