I should be getting the Artec invader copy next week
- Thread starter solspirit
- Start date
Artie
Peaveyologist
Sensimilla and I like these CTS push-pulls:
https://guitarelectronics.com/cts-500k-audio-taper-pot-w-push-pull-switch
I'd do series / parallel with an Invader. (In fact, I am.) Keeps it hum-cancelling and parallel is still close to split tone, but better, IMHO.
(J/K. I haven't toked since SE Asia.)
https://guitarelectronics.com/cts-500k-audio-taper-pot-w-push-pull-switch
I'd do series / parallel with an Invader. (In fact, I am.) Keeps it hum-cancelling and parallel is still close to split tone, but better, IMHO.
(J/K. I haven't toked since SE Asia.)
ehdwuld
A Ficus
if you are going to set it up as a single humbucker with a single volume
I would use a 500k pot linear taper
you could also use a one meg pot with a one meg resistor across the outer legs to make it look like a 500 k to the pickup
and give you a different taper as you roll it down
not exactly like an audio taper but similar
if you are going to use a tone pot then use a .022 cap
what would you want to use the push pull for
I would use a 500k pot linear taper
you could also use a one meg pot with a one meg resistor across the outer legs to make it look like a 500 k to the pickup
and give you a different taper as you roll it down
not exactly like an audio taper but similar
if you are going to use a tone pot then use a .022 cap
what would you want to use the push pull for
Artie
Peaveyologist
Series / Parallel is sweet with an Invader. Even a copy.
Agreed. Even split is pretty good.
solspirit
Ultimate Post Liker
This is what I was thinking.
solspirit
Ultimate Post Liker
Why? 500 A or b?
solspirit
Ultimate Post Liker
I think that's what the Busker's has.
. I suppose I could both with the addition of a mini switch.
idsnowdog
Imperator of Indignation
Large ceramic magnets, large polepieces, higher resistance, and a brass baseplate will probably equal a dark/thick humbucker. A 500K might be fine but I use 1 meg for high output pickups.
ehdwuld
A Ficus
solspirit
Ultimate Post Liker
Ok, it's here, tried to take a pic, but, you know.
Now it will probably take a week to dig out the tools and make a workspace.
I'll use the 1 meg DiMarzio "custom taper" more linear than anything imo.
What about caps?
That rules out the push/push pot, I could do it with a 500k pot, but I don't have any 1 meg push/push or pull.
Maybe down the road, I need to see if I'll even like it with the 1 meg.
I can always add to it, but I just can't subtract what it is, the bare necessinecessities.
Now it will probably take a week to dig out the tools and make a workspace.
I'll use the 1 meg DiMarzio "custom taper" more linear than anything imo.
What about caps?
That rules out the push/push pot, I could do it with a 500k pot, but I don't have any 1 meg push/push or pull.
Maybe down the road, I need to see if I'll even like it with the 1 meg.
I can always add to it, but I just can't subtract what it is, the bare necessinecessities.
Coma
Well-known member
Can confirm. Back when I was using them, I rewired a bridge Invader to parallel just out of curiosity. It was surprisingly good, as I recall.
Artie
Peaveyologist
I've often referred to it as a pickup (PAF?) hidden in a pickup.
