Installing New Pickups Assistance Needed

[liamgray]

Hello there
I have just brought 3 New pick-ups
and all new volume, 5 way import switch, pretty much everything electrical
I have Sh-13 dimebucker
Scr-n Cool rails Neck
SHR-N Hot rails Neck

Would any one have an wiring as there is not one available on seymour wiring list
1 humbucker
2 Single Coils
250k Tone Push/Pull
250k Volume
5 way Import Switch

This is for A SuperStrat Washburn KC-40v
Thank You
Liam

 

[AniML]

Re: Installing New Pickups Assistance Needed

Unless you were planning a coil split,its the Same as 3 single coils

 

[liamgray]

Re: Installing New Pickups Assistance Needed

Unless you were planning a coil split,its the Same as 3 single coils

Yer that will split the humbuck thats what i am trying to achive
otherwise i wouldnt need the push pull tone

 

[AniML]

Re: Installing New Pickups Assistance Needed

There should be a coil split diagram in Seymour's wiring page.

 

[Marc Burger]

Re: Installing New Pickups Assistance Needed

bridge humbucking is
black to hot
green to ground and
red and white linked (series).
to split connect red and white to middle lug of push pull switch part and another wire from top or bottom pin of switch to ground.
(2 rows of 3 pins both do the same, middle connects to top or bottom, depending on switch up or down).
when switch not engaged red and white connected only to each other meaning normal series humbucker.
when switch engaged all red, white and green are going to ground, meaning only the coil that starts with black and ends with white will give a signal (split to slug coil).
Good luck

 

[liamgray]

Re: Installing New Pickups Assistance Needed

bridge humbucking is
black to hot
green to ground and
red and white linked (series).
to split connect red and white to middle lug of push pull switch part and another wire from top or bottom pin of switch to ground.
(2 rows of 3 pins both do the same, middle connects to top or bottom, depending on switch up or down).
when switch not engaged red and white connected only to each other meaning normal series humbucker.
when switch engaged all red, white and green are going to ground, meaning only the coil that starts with black and ends with white will give a signal (split to slug coil).
Good luck

Thank you for that
Ill try digest that
this is first wiring job
i Think i understand its only the humbucker being split is that correct

 

[GuitarDoc]

Re: Installing New Pickups Assistance Needed

correct.

 

[GuitarDoc]

Re: Installing New Pickups Assistance Needed

I think this is what you need...

http://www.seymourduncan.com/support/wiring-diagrams/schematics.php?schematic=1h_2s_1v_1t_5w_pp

 

[liamgray]

Re: Installing New Pickups Assistance Needed

I think this is what you need...

http://www.seymourduncan.com/support/wiring-diagrams/schematics.php?schematic=1h_2s_1v_1t_5w_pp

Thanks but there is a problem
That's for split volume I have split tone
That's standard wiring
I had red and black coming from humbucker
But that's washburn wiring
I have soldering today Im guessing its just red and white

Because green and bare are earth
Black goes to 5 way
Do you recon the wires would go same place on the push pull volume shown in the diagram for a tone version

 

[AlexR]

Re: Installing New Pickups Assistance Needed

Yes,

You just put the split wiring part and solder it to the lugs on whichever pot has the push-pull.

If you've got seymour duncan pickups going in then you need to follow the SD wiring scheme.

 

[GuitarDoc]

Re: Installing New Pickups Assistance Needed

It doesn't matter which pot the push/pull is on. It is wired just the same.

Here is a color coding chart that may be helpful:

http://www.seymourduncan.com/support/wiring-diagrams/schematics.php?schematic=color_codes