Invader pickup in SG

[xStonr]

I recently installed an Invader in the bridge position of my SG. I was looking for less high end out of my bridge pickup which is why I got the Invader. I'm a little disappointed since it still sounds shrilly. Could I have wired it wrong? I'm open to suggestions.

 

[PRG]

Re: Invader pickup in SG

That's wierd. Try adjusting the height of the pickup, as well as your amp settings. The Invader is sludge-city in my SG, even with the amp's bass on "half", it's still to muddy. It sounds practically like a neck pickup, bassy with little treble to speak of. You might have wired it backwards. I believe Black is the power wire and the Green and Bare are used as the ground wire. Then just twist the White and Red together, solder 'em, and tape over the wire.

 

[Marcel]

Re: Invader pickup in SG

I recently installed an Invader in the bridge position of my SG. I was looking for less high end out of my bridge pickup which is why I got the Invader. I'm a little disappointed since it still sounds shrilly. Could I have wired it wrong? I'm open to suggestions.

what do mean with shrilly something like harsh?

 

[korinastratkyle]

Re: Invader pickup in SG

It actually has a little bit of a brightness factor to it, so does the guitar you have it in. Anyways, what value pots are you using? Caps on the tone pot? You may want to lower to a 300K or 250K if it's 500K or increase the size of the tone cap. If it's like a really nasty peak shrill sound lowering the value of the pots (simulated by turning the volume knob on your guitar down to 9 or 8) would be what does the trick.

 

[Hellion]

Re: Invader pickup in SG

I have an Invader in one of my SG's and it sounds like God. It sustains better than any other guitar I own (including a 13 lb Les Paul Custom and a Washburn Falcon) and I haven't had any problems with it being too shrill or anything except loud. Might be the wiring.

 

[xStonr]

Re: Invader pickup in SG

what do mean with shrilly something like harsh?

It's much brighter than I thought.

I'm not sure about the value of my pots, but I have been considering swapping out all the electronics since I got this guitar used.

 

[Metalman_666]

Re: Invader pickup in SG

these guys are right, its most likely the wiring, or maybe the pots. if you have 500k get the 300k pots with the Invader; its in between too weak and too strong.

 

[jeremy]

Re: Invader pickup in SG

with an invader thats being to toppy, id use a 500k volume pot and 250k tone pot

 

[Fusion1]

Re: Invader pickup in SG

An Invader in my SG was a mud-machine with the standard 300K pots. I tried various capacitors and still nothing but that sloppy mud sound. The Distortion that replaced it was better but still too loose.

 

[xStonr]

Re: Invader pickup in SG

I've decided to replace all the pots, caps, switch,and wiring in the SG. I ordered cts 500k pots and .047 Microfarad caps. I will rewire to the diagram I got called the Ultimate SG wiring. So I'll update ya all when this gets done.

 

[Hellion]

Re: Invader pickup in SG

Begging your pardon, but that sounds like a lot of work for a set up that should sound like the 2nd coming to begin with. My 75 SG with the Invader in the bridge doesn't take any prisoners! I'd like to see the wiring, though....

 

[Empty Pockets]

Re: Invader pickup in SG

Hey, when you're done with all that wiring, will you sell me your SG?