Covers without potting?
- Thread starter ShredMAN
- Start date
STRATDELUXER97
Stratoblaster Tone Meister
Re: Covers without potting?
Not at all....Just put a piece of masking tape over all of the slugs and make sure you get the cover on the pickup tight...I usually clamp the cover and then solder it..Just clamp the cover snug enough to hold it down but not so tight that it dents the top of the cover and you'll be fine...
John
Not at all....Just put a piece of masking tape over all of the slugs and make sure you get the cover on the pickup tight...I usually clamp the cover and then solder it..Just clamp the cover snug enough to hold it down but not so tight that it dents the top of the cover and you'll be fine...
John
STRATDELUXER97
Stratoblaster Tone Meister
Re: Covers without potting?
Sometimes pictures are worth a 1000 words so here's a link to one of my tutorials that will help you out...
http://www.projectguitar.com/tut/barmagswap.htm
STRATDELUXER97 said:
Sometimes pictures are worth a 1000 words so here's a link to one of my tutorials that will help you out...
http://www.projectguitar.com/tut/barmagswap.htm
ledzepp29
New member
Re: Covers without potting?
I put a peice of masking tape over the slugs of my covered humbucker but I could only do it on the neck humbucker because the bridge humbuckers cover would not come off for anything so I just let it be. its not that big of a problem unless you have your gain high on the distortion channel. but since my stock pups are hot I only use like 4 1/2 gain. no squeal. but if you use high gain then they will squeal when you face the amp.
I put a peice of masking tape over the slugs of my covered humbucker but I could only do it on the neck humbucker because the bridge humbuckers cover would not come off for anything so I just let it be. its not that big of a problem unless you have your gain high on the distortion channel. but since my stock pups are hot I only use like 4 1/2 gain. no squeal. but if you use high gain then they will squeal when you face the amp.
Gearjoneser
Gear Ho
Re: Covers without potting?
Just dig the tip of the soldering iron in between the pot and wire, just long enough to turn the solder wet, then pull the wire out. I hate it when the solder is stubborn and won't melt! Just memorize or draw a little diagram of where your original leads went, then install the new pickups the same way.
On stock pickups with a black positive and shielded negative, just take the new Duncan pickup, twist and solder the red and white leads together. The Duncan black wire is positive, and the green and plain wire are negative, and you twist and solder those together. They get soldered to the pot body.
ledzepp29 said:
Just dig the tip of the soldering iron in between the pot and wire, just long enough to turn the solder wet, then pull the wire out. I hate it when the solder is stubborn and won't melt! Just memorize or draw a little diagram of where your original leads went, then install the new pickups the same way.
On stock pickups with a black positive and shielded negative, just take the new Duncan pickup, twist and solder the red and white leads together. The Duncan black wire is positive, and the green and plain wire are negative, and you twist and solder those together. They get soldered to the pot body.
STRATDELUXER97
Stratoblaster Tone Meister
Re: Covers without potting?
I always use some form of heat sink on the opposite end of the heat(Between the terminal and the soldering iron)...I Like hemostats or Radio Shack sells a little clip on heat sink...Better to let the tool take the heat rather than your pot or cap etc...It's just alot safer this way..
John
ledzepp29 said:
I always use some form of heat sink on the opposite end of the heat(Between the terminal and the soldering iron)...I Like hemostats or Radio Shack sells a little clip on heat sink...Better to let the tool take the heat rather than your pot or cap etc...It's just alot safer this way..
John
