Impedence on pickups
- Thread starter destry17
- Start date
Artie
Peaveyologist
Re: Impedence on pickups
Hey destry; Your question is a little bit vague as to what your asking. Do you mean as in two supposedly identical pickups, like a pair of 59n's, that happen to measure slightly differently in ohms?
For example, one 59n measures 7.42k and one measures 7.45k.
Is that what you mean?
Hey destry; Your question is a little bit vague as to what your asking. Do you mean as in two supposedly identical pickups, like a pair of 59n's, that happen to measure slightly differently in ohms?
For example, one 59n measures 7.42k and one measures 7.45k.
Is that what you mean?
Evan Skopp
SDUGF Founder
Re: Impedence on pickups
Perhaps you can explain what you mean by impedance. Are you really referring to resistance to alternating current, which varies by frequency? Or are you referring to resistance to direct current?
Perhaps you can explain what you mean by impedance. Are you really referring to resistance to alternating current, which varies by frequency? Or are you referring to resistance to direct current?
Re: Impedence on pickups
I am replacing a Godin pickup with a Hotrail. It hadn't really thought about there being variation in power, sensitivity, and output of different pickups. I am learning as I go. So the question is, is it a problem (will it cause me problems) to mix two similar style pickups made by different folks. I picked Duncan pickups because some Godin guitars are using them now. It is on an old ST1 I am trying to rebuild.
I am replacing a Godin pickup with a Hotrail. It hadn't really thought about there being variation in power, sensitivity, and output of different pickups. I am learning as I go. So the question is, is it a problem (will it cause me problems) to mix two similar style pickups made by different folks. I picked Duncan pickups because some Godin guitars are using them now. It is on an old ST1 I am trying to rebuild.
Re: Impedence on pickups
Only problem is if one is greatly louder than the other, and that's only a problem if you mind. Some people mismatch output level intentionally, some try to get both matched up. In general you want you bridge pup a bit louder than your neck pup, although with equal power pups you can lower the neck pup a bit to accomplish a similar thing as well. The only real way to know is to replace it, if it's to loud then you can always lower it a bit, and as a plus get lower string pull (a bit more sustain and harmonics from the string). It should work out just fine if it's going in the bridge. Is it a strat style guitar, if so the bridge and middle position should even out a bit more regardless.
destry17 said:
Only problem is if one is greatly louder than the other, and that's only a problem if you mind. Some people mismatch output level intentionally, some try to get both matched up. In general you want you bridge pup a bit louder than your neck pup, although with equal power pups you can lower the neck pup a bit to accomplish a similar thing as well. The only real way to know is to replace it, if it's to loud then you can always lower it a bit, and as a plus get lower string pull (a bit more sustain and harmonics from the string). It should work out just fine if it's going in the bridge. Is it a strat style guitar, if so the bridge and middle position should even out a bit more regardless.
Re: Impedence on pickups
The pup's tone is the first consideration, output level second in this case ... You don't want a pup that is WAY louder than the bridge though, as that does get a bit hard to balance volume wise, but a little bit louder you can get away with, especially if the pup's tone is a bit brighter than the bridge pup.
destry17 said:
The pup's tone is the first consideration, output level second in this case ... You don't want a pup that is WAY louder than the bridge though, as that does get a bit hard to balance volume wise, but a little bit louder you can get away with, especially if the pup's tone is a bit brighter than the bridge pup.
Similar threads
