Ohms?
- Thread starter StratTom
- Start date
Artie
Peaveyologist
Re: Ohms?
Someone else, (with more amp experience than me), can comment on the sonic side of this question, but from a strictly electrical point of view, I'ld prefer 16 ohms for two reasons.
16 ohms means lower current. Lower current equates to less heat.
Also, if you want to add a second cab later, in parallel, it drops you to 8 ohms, which is still a nice middle-of-the-road number.
Just my 2-ohms worth.
Someone else, (with more amp experience than me), can comment on the sonic side of this question, but from a strictly electrical point of view, I'ld prefer 16 ohms for two reasons.
16 ohms means lower current. Lower current equates to less heat.
Also, if you want to add a second cab later, in parallel, it drops you to 8 ohms, which is still a nice middle-of-the-road number.
Just my 2-ohms worth.
TwilightOdyssey
Darkness on the edge of Tone
Re: Ohms?
You should get the Avatar that has the same impedence as your Peavey cab.
You should get the Avatar that has the same impedence as your Peavey cab.
TwilightOdyssey
Darkness on the edge of Tone
Re: Ohms?
The 5150 cab is 16 Ohms, I believe, but you should check the back to make sure.
The 5150 cab is 16 Ohms, I believe, but you should check the back to make sure.
proxy
New member
Re: Ohms?
Wouldn't it be the opposite? For example Its safe to have an amp expecting an 8 ohm cab but actually having a 16, or a 4 to 8, but not a 16 to 8 or 8 to 4. Because the voltage has to be dropped to a safe level before it comes into the amp. An 8 ohm amp will have a smaller voltage drop then lets say a 16 ohm.
ArtieToo said:Someone else, (with more amp experience than me), can comment on the sonic side of this question, but from a strictly electrical point of view, I'ld prefer 16 ohms for two reasons.
16 ohms means lower current. Lower current equates to less heat.
Also, if you want to add a second cab later, in parallel, it drops you to 8 ohms, which is still a nice middle-of-the-road number.
Just my 2-ohms worth.
Wouldn't it be the opposite? For example Its safe to have an amp expecting an 8 ohm cab but actually having a 16, or a 4 to 8, but not a 16 to 8 or 8 to 4. Because the voltage has to be dropped to a safe level before it comes into the amp. An 8 ohm amp will have a smaller voltage drop then lets say a 16 ohm.
Re: Ohms?
If you have taps on your amplifier (4, 8 , and 16) you can match speaker boxes with any of those impedances; so get what you want for other reasons. You want to match in order to get the maximum power. Mismatching will not hurt the amplifier, but will give you less power. (However, in general you should not play an amplifier without any speaker at all; this might damage the output trasnformer, unless it has been designed to handle this, as some are.) If you use two speaker boxes each 8 ohms and connect them in parallel (that is, connect the similar wires of each together, a separate path to each speaker box) use the 4 ohm tap. You could connect two 8s in series (run through one, then the other, and then back to the amp); then use the 16 ohm tap.
If you have taps on your amplifier (4, 8 , and 16) you can match speaker boxes with any of those impedances; so get what you want for other reasons. You want to match in order to get the maximum power. Mismatching will not hurt the amplifier, but will give you less power. (However, in general you should not play an amplifier without any speaker at all; this might damage the output trasnformer, unless it has been designed to handle this, as some are.) If you use two speaker boxes each 8 ohms and connect them in parallel (that is, connect the similar wires of each together, a separate path to each speaker box) use the 4 ohm tap. You could connect two 8s in series (run through one, then the other, and then back to the amp); then use the 16 ohm tap.
