TELE Duncan Little 59 / 59 NECK SERIES PARALLEL WIRING ONE PUSH PULL TONE POT
- Thread starter Funkyard
- Start date
Re: TELE Duncan Little 59 / 59 NECK SERIES PARALLEL WIRING ONE PUSH PULL TONE POT
i dont think you can use one push/pull (dpdt switch) to do series/parallel for two pups. you'd need a 4pdt push/pull. you can split two pups with a typical p/p since each pup only needs one side of the switch, but series/parallel takes all the contacts
i dont think you can use one push/pull (dpdt switch) to do series/parallel for two pups. you'd need a 4pdt push/pull. you can split two pups with a typical p/p since each pup only needs one side of the switch, but series/parallel takes all the contacts
Re: TELE Duncan Little 59 / 59 NECK SERIES PARALLEL WIRING ONE PUSH PULL TONE POT
Wait, are you trying to do each pickup with its own series parallel switch, or do you want 1 switch to select between one pickup in series with the other, and one pickup in parallel with the other? If you want option A, you would need a 4 conductor 59.
Wait, are you trying to do each pickup with its own series parallel switch, or do you want 1 switch to select between one pickup in series with the other, and one pickup in parallel with the other? If you want option A, you would need a 4 conductor 59.
Re: TELE Duncan Little 59 / 59 NECK SERIES PARALLEL WIRING ONE PUSH PULL TONE POT
Or are you asking about having the p/p pot to put the bridge pup in series or parallel with the neck pup? That can be done with one p/p. But if you mean to put EACH pup in series or parallel you'd need 2 p/p pots (I've never seen a 4PDT p/p pot).
Or are you asking about having the p/p pot to put the bridge pup in series or parallel with the neck pup? That can be done with one p/p. But if you mean to put EACH pup in series or parallel you'd need 2 p/p pots (I've never seen a 4PDT p/p pot).
Re: TELE Duncan Little 59 / 59 NECK SERIES PARALLEL WIRING ONE PUSH PULL TONE POT
Thanks for your replies ordered s 2nd push pull tone pot for neck. You never know until you ask!!!
Thanks for your replies ordered s 2nd push pull tone pot for neck. You never know until you ask!!!
kevindirks
New member
Looking for some help finding a wiring diagram on an alternate 4 way switch wiring for a HS Tele that I am having difficulty finding (maybe not even possible?). I am putting in a Seymour Duncan Little 59 in the Bridge and want the option of series/parallel
What I want…
Position 1: Bridge HB Series
Position 2: Bridge HB Parallel
Position 3: Bridge HB/Neck Single (Stock) Parallel
Position 4: Neck Single (Stock)
My Tele (2021 Squier Affinity Tele) is pretty thin and might even have trouble using the new lower profile CTS Pots with the circuit board…so I thought I might try to find out if the above is possible.
What I want…
Position 1: Bridge HB Series
Position 2: Bridge HB Parallel
Position 3: Bridge HB/Neck Single (Stock) Parallel
Position 4: Neck Single (Stock)
My Tele (2021 Squier Affinity Tele) is pretty thin and might even have trouble using the new lower profile CTS Pots with the circuit board…so I thought I might try to find out if the above is possible.
eclecticsynergy
Well-known member
I don't think a plain 4-way could do that for you. Then again, I'm no expert especially when it comes to a 4-way.
Certainly could be done with a Superswitch. You'd get a fifth position to play with too.
Maybe split bridge in parallel with the neck, to sort of approximate classic Tele middle position?
Still, a Superswitch is fairly big - not sure there'd be room for one in your Squier.
